In the U. A, for questions about features,. Previous Page. Next Page. Do not install the refrigerator in a damp place or a place where it may come in contact with water. Page 3 If the refrigerator is not to be used for a long period of time, pull out the power plug.
If not, check the power supply and electricity source. Place the refrigerator in an appropriate location with reasonable clearance between the wall and the refrigerator. BUTTON To set the freezer temperature, press the button repeatedly to change the set temperature in sequence between cold and coldest.
Power Freeze Power Freeze speeds up the freezing process. Adjust temperature gradually: push the button in small increments, allowing the temperature to stabilize. Page 8: Shelves And Bins Preparing to Move Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.
This could damage the refrigerator. Handle only from the sides of the refrigerator. Then lift it up and remove it. Clean the doors with a mild detergent and damp cloth. Then wipe with a dry cloth. If you have difficulty in changing the lights, contact your service center. DOORS The refrigerator doors have a special door opening and closing feature to make sure they close all the way and are securely sealed. Allow sufficient space to circulate the air at the internal cooling system.
Be careful not to cut the water tube when separating it from the coupler. Removing the Freezer Door Unplug the refrigerator before removing the doors. Carefully place front cover and push to snap it into position.
Reattaching the Front Leg Cover Put on the front leg cover by turning the three screws clockwise, as shown in the figure. The doors will be uneven if the refrigerator is not level. Case 1 Freezer door is lower than the fridge door. For newer Samsung refrigerators, you will need to press Freezer, Energy Save, and Lighting simultaneously. In some cases you will need to press Freezer, Energy Save, and Fridge and hold them simultaneously for about 10 seconds. To reset your Samsung refrigerator control panel, simply press the Power Cool and Power Freeze buttons at the same time, and hold for about 10 seconds until you see the numbers on the display reset.
But what if your control panel is not displaying or the buttons are not working at all? Carry out a general reset by following the steps above. To deactivate the child lock feature on your Samsung refrigerator, simply press and hold the child lock button for a few seconds. In the absence of one depending on the model , follow the steps provided for your model in the product manual.
To reset your control panel display, locate the reset switch at the top of the right door interior side and switch it off and then on again. The unit will reboot and the Samsung logo will appear on the panel. Need expert help? Use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting. At times, the display might blink an error code indicating that there is a communication problem between the refrigerator door and the main control unit.
If it is, simply reconnect. If it is in place, still disconnect it and then reconnect it back. Then plug it in and switch on the refrigerator. It would have removed the error code. To reset a Samsung fridge touch screen, find a red switch on top of the fridge This red switch is behind a small panel on the right door.
The panel has Push written on it. Flip the red switch and then flip it back to its original position again. Your touch screen should start working now.
Do you own a different brand of refrigerator that needs resetting? Check out these articles…. Go to the control panel or touch screen display Some Samsung refrigerator models have theirs inside the fridge while others have their displays outside. Press the fridge button to display the current temperature The temperature ranges from 34 to 44 degrees Fahrenheit.
Keep pressing the fridge button until you get to your desired temperature. Assuming you want to increase the temperature to 37 degrees and it is currently at 35 degrees, tapping the button once will take the temperature to 34 degrees which happens to be the lowest temperature for the fridge.
You can then press the button again to take it to 43 and so on until it gets to Important note: The temperature setting does NOT have up or down buttons but goes in circles from 44 degrees down to 34 degrees and back to 44 degrees. Step 1: Locate the control panel Depending on the model of Samsung refrigerator you own, it could either be inside the fridge or outside.
Step 2: Press the freezer button until you get to your desired temperature. Note that on some freezers, you will have to hold it for about 5 seconds so it stays on the temperature you set it on.
Also note that the freezer temperature circles from -8 degrees to -7, -6, -5 and so on until you get to 5 degrees and back again. For video demonstration of how to reset the temperature of the freezer of a Samsung refrigerator, watch the video below….
To reset your Samsung fridge after a power outage, press the power save and lighting buttons for 10 seconds or press the fridge and freezer buttons at the same time for 10 seconds. Holding the fridge and freezer buttons at the same time will reset the refrigerator and remove these error codes. However, you should try the power save and lighting buttons option first before resetting your refrigerator.
Pull out the ice tray. Locate the reset button. Look to the side. You should see the blue reset button there. Hold down the reset button till you hear a beep. This will reset your ice maker. You can reset your Samsung refrigerator 22E error code by pressing the power and lighting buttons on the display and holding them down for 8 to 10 seconds.
The 22E error code only shows when your machine is not performing well or is broken. This error code can be caused by blade lock, water stagnation in the drainage, clogged vent hole, circuit board damage, melting system failure, motor problems, or wiring discontinuity.
If you try pressing the recommended buttons on the display and the error code does not go off, then you can check each of the possible problems individually. To reset your Samsung refrigerator 33E error code, reboot the electronic control board by plugging the refrigerator into the power outlet and press the energy saver and lighting buttons for 8 to 10 seconds.
0コメント